What did you do to your Warrior Today??? - Page 633 - Road Star Warrior Forum : Yamaha Star Warrior Forums

Reply
 
LinkBack Thread Tools
Old 08-18-2019, 10:24 AM   #6321 (permalink)
Senior Member
 
Join Date: Jun 2019
Location: McHenry Illinois
Posts: 135
Default

Yes that is the plan, all I need now is the correct banjo fitting
flyingmerkel54 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old 08-18-2019, 11:54 AM   #6322 (permalink)
Senior Member
 
Desertboy13's Avatar
 
Join Date: Aug 2012
Location: COACHELLAVALLEY
Posts: 6,032
Default

What Banjo fitting are u referring to?.?

My 2 line setup came with 6 brake line washers...

Was a ez n simple install

Sent from my SAMSUNG-SM-J327A using Tapatalk
Desertboy13 is online now   Reply With Quote
Old 08-18-2019, 04:51 PM   #6323 (permalink)
Senior Member
 
evilrider's Avatar
 
Join Date: Feb 2009
Location: oklahoma city ok
Posts: 3,227
Default

the machine has been down for a couple of weeks now. I looked at it today and got a little sad. its been over 100 degrees the whole time so its probably best. I hope its just a sensor that's caused the front cylinder to stop working. I made the stupid mistake of pulling the sensor before looking at the error codes. ive been busy with a project so I haven't touched it. I hope next week I will be able to get the machine back to its former glory and tearing up the roads again.
evilrider is offline   Reply With Quote
 
Old 08-18-2019, 07:17 PM   #6324 (permalink)
Senior Member
 
Join Date: Jun 2019
Location: McHenry Illinois
Posts: 135
Default

I need a double deep banjo fitting for the MS cuz two lines connect at the MS in this set up
flyingmerkel54 is offline   Reply With Quote
Old 08-18-2019, 09:20 PM   #6325 (permalink)
Senior Member
 
Desertboy13's Avatar
 
Join Date: Aug 2012
Location: COACHELLAVALLEY
Posts: 6,032
Default

Oh are u talking about the bolt ?.?.
Post some pics

Sent from my SAMSUNG-SM-J327A using Tapatalk
Desertboy13 is online now   Reply With Quote
Old 08-20-2019, 06:02 AM   #6326 (permalink)
Senior Member
 
JV_Warrior's Avatar
 
Join Date: Aug 2018
Location: Vienna, WV
Posts: 492
Default

Installed 3Ē peg extension. Feels so much better to be able to stretch my legs out more. Riding position is a lot different. I had bought a set a few months ago and only put the right side on and didnít like it. Decided to give it another chance and fully installed it this time. Only put about 50 miles with them on but itís a world of difference. No longer feel crammed on the bike. Anyone 6í or taller I highly recommend them.


Sent from my iPhone using Tapatalk
JV_Warrior is offline   Reply With Quote
Old 08-20-2019, 07:04 PM   #6327 (permalink)
Senior Member
 
i-man's Avatar
 
Join Date: Sep 2015
Location: Atlanta, GA/Fontana Dam, NC
Posts: 495
Default

Left side cleanup complete. Motor mount modified for coil bracket. Dyna coils and Taylor wires installed. Pulley mod complete. New plugs installed.
Tomorrow, tank goes back on, map gets loaded to new PCV and she gets fired up.

Sent from my SM-N960U using Tapatalk
i-man is offline   Reply With Quote
Old 08-21-2019, 01:18 AM   #6328 (permalink)
Senior Member
 
FlySpur's Avatar
 
Join Date: Nov 2018
Location: City by the Bay, CA
Posts: 161
Default

Been trying to take the shock apart. But still no luck. I canít unscrew the top nut.
Wanted to replace the spring with Eibach.
__________________
2002 Yamaha Warrior

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
FlySpur is offline   Reply With Quote
Old 08-21-2019, 01:25 AM   #6329 (permalink)
Senior Member
 
Desertboy13's Avatar
 
Join Date: Aug 2012
Location: COACHELLAVALLEY
Posts: 6,032
Default

Ok ..
You have to compress the Spring down..
And than look for a wire clip n remove the wire clip and remove the locking nuts
And than the Spring can be taken out ..

Just keep the Spring compress with a Spring tool ..
I used some bailing wire..

To install the Ebachi Spring...
You wont need to compress the Ebachi Spring cause Its actually shorter than the OE one..
Drop the Ebachi Spring in and reinstall the wire clip and than the locking nuts...

Sent from my SAMSUNG-SM-J327A using Tapatalk
Desertboy13 is online now   Reply With Quote
Old 08-21-2019, 01:37 AM   #6330 (permalink)
Senior Member
 
FlySpur's Avatar
 
Join Date: Nov 2018
Location: City by the Bay, CA
Posts: 161
Default

Thanks bud! I read or may be I misunderstood the whole process. Here is what I mean. I saw this in one of the docs :


Also read that you donít need to compress 03+ shock. Because after unscrewing the nut there is no force left on the spring..
__________________
2002 Yamaha Warrior

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
FlySpur is offline   Reply With Quote
Sponsored Links
Advertisement
 
Reply

  Road Star Warrior Forum : Yamaha Star Warrior Forums > Warrior Forums > General Discussion

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -4. The time now is 09:01 AM.


Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
RSWarrior.com is an independent Yamaha enthusiast website. Content on RSWarrior.com is generated by its users and RSWarrior.com is not in any way affiliated with Yamaha Motor Corporation, U.S.A.